- How to install smargo on debian how to#
- How to install smargo on debian serial#
- How to install smargo on debian drivers#
- How to install smargo on debian full#
Usb 1-1: configuration #1 chosen from 1 choiceĭrivers/usb/serial/usb-serial.c: USB Serial support registered for generic
How to install smargo on debian full#
Usb 1-1: new full speed USB device using uhci_hcd and address 2 If linux is UP plug smartreader to USB and wait little so 20 second. Now disconnect smartreader+ disable from CCcam smartreader+ config lines and make restart to linux PC.
How to install smargo on debian how to#
You will find inside that "smartreader_v103.zip" very precise how to update that device. Make sure that your installed linux distro wich has kernel 2.6.12 or newer version!Ģ: Update your smartreader+ if it has v1.2 or older firmware with v1.3 Link to download: hereģ: Before update make sure your reader is 100% reconized by linux! Here is little help how to setup smartreader+ successfully under linux PC. Tutorial for Smargo Smartreader for linux PC The configuration in the above post will only work with pli-enigma2 jade dm800 31st Oct 08. SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 9610002 runs the card at 9.61mhz.įor latest PLI image released on 31st Jan 09, please add the below lines to your CCcam.cfg file. SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 8000002 runs the card at 8mhz. SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6860002 runs the card at 6.86mhz. SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6000002 runs the card at 6mhz.
The above cfg's assume that the reader is set to autoswitch mode and dreambox kernel. However if you wish to add a usb hub you can. The DM800 comes with 2 USB ports already. SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 6860002 SERIAL READER : /dev/ttyUSB0 smartreader+ SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/3 6860002 SERIAL READER : /dev/usb/tts/3 smartreader+ SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/2 6860002 SERIAL READER : /dev/usb/tts/2 smartreader+ SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/1 6860002 SERIAL READER : /dev/usb/tts/1 smartreader+ To incorporate a 4 port hub into the config insert the following: It is possible to add a usb hub to the DM7020. SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6860002 SERIAL READER : /dev/usb/tts/0 smartreader+ Make sure the chip on the card faces the same direction as the lights on the reader. So no need to replace the bootup file.ĭM800 dreambox installation with PLI Iolite/JadeĦ: Insert your card. * The latest PLi Jade Final image appears to already have the usbtoserial configured in the bootup file. The bootup file is in the zipfile.Ĩ: Insert your card.
How to install smargo on debian drivers#
How to set smartreader operating mode using Windows (It did not work for it in Vista for me, It worked in XP)ġ: Install the windows drivers found here Smartreaderplus DriversĦ: Make sure it returns with "writing settings successful"ĭM7020 dreambox installation with PLI Iolite/Jadeġ: Telnet to your dreambox run "ipkg update"Ģ: Run "ipkg install kernel-module-ftdi-sio"Ĥ: Rename your original bootup file in /etc/init.d/ incase you have a problem*ĥ: Replace the bootup file in /etc/init.d/ with this one Smartreaderplus Drivers. The tutorial can be used as it is, or adapted easily for a standard Linux setup. This tutorial assumes the user has a DM7020 or a DM800.
0 kommentar(er)
